Description
Inkubator saya di rumah di mana saja di dunia penelitian, kedokteran, farmasi dan analisis makanan, serta kimia makanan.
Incubator
IN30 The incubator I is at home everywhere in the world of research, medicine, pharmaceutics and food analytics, as well as food chemistry.
The heating of this incubator is optimally tuned for both natural convection and forced air circulation; the fan can
also be switched off completely, and valuable chamber loads for research, pharmaceutics, medicine and food
chemistry are warmed up very carefully.
On this page, you can find all the essential technical data on our incubator. Our customer relations team will be
pleased to help if you want further information. If you should require a customised special solution, please contact
our technical specialists at myAtmoSAFE@memmert.com.
Temperature
Set temperature range in °C min. 5°C above ambient up to +80°C
Setting accuracy
temperature
0.1 °C
Temperature 1 Pt100 sensor DIN class A in 4-wire-circuit
Control technology
Language setting German, English, Spanish, French, Polish, Czech, Hungarian
ControlCOCKPIT SingleDISPLAY. Adaptive multifunctional digital PID-microprocessor controller with high-definition
TFT-colour display
Timer Digital backwards counter with target time setting, adjustable from 1 minute to 99 days
Function SetpointWAIT the process time does not start until the set temperature is reached
Calibration three freely selectable temperature values
adjustable parameters temperature (Celsius or Fahrenheit), air flap position, programme time, time zones,
summertime/wintertime
Ventilation
Convection natural convection
Fresh air admixture adjustment of pre-heated fresh air admixture by air flap control in 10 % steps
Vent vent connection with restrictor flap
Communication
Documentation programme stored in case of power failure
Programming AtmoCONTROL software for reading out, managing and organising the data logger via Ethernet
interface (temporary trial version can be downloaded). USB stick with AtmoCONTROL software
available as accessory (on demand).
Safety
Temperature control adjustable electronic overtemperature monitor and mechanical temperature limiter TB, protection class
1 according to DIN 12880 to switch off the heating approx. 20°C above nominal temperature
Autodiagnostic system for fault analysis
Standard equipment
Door fully insulated stainless steel door with 2-point locking (compression door lock)
Internals 1 stainless steel grid(s), electropolished
Works calibration certificate incl. works calibration certificate for +37°C
Door inner glass door
Page 2/4 | 26.03.2018 | 26.03.2018
Memmert GmbH + Co. KG | Tel. +49 (0) 9122/925-0 | E-Mail info@memmert.com
Memmert Incubator IN30 – en
Stainless steel interior
Interior easy-to-clean interior,made of stainless steel, reinforced by deep drawn ribbing with integrated and
protected large-area heating on four sides
Volume 32 l
Dimensions w
(A) x h(B) x d(C): 400 x 320 x 250 mm
Max. number of internals 3
Max. loading of chamber 60 kg
Max. loading per internal 20 kg
Textured stainless steel casing
Dimensions w
(D) x h(E) x d(F): 585 x 704 x 434 mm
Housing rear zinc-plated steel
Electrical data
Voltage
Electrical load
230 V, 50/60 Hz
approx. 1600 W
Voltage
Electrical load
115 V, 50/60 Hz
approx. 800 W
Ambient conditions
Set Up The distance between the wall and the rear of the appliance must be at least 15 cm. The clearance
from the ceiling must not be less than 20 cm and the side clearance from walls or nearby appliances
must not be less than 5 cm.
Altitude of installation max. 2,000 m above sea level
Ambient temperature +5 °C to +40 °C
Humidity rh max. 80 %, non-condensing
Overvoltage category II
Pollution degree 2
Packing/shipping data
Transport information The appliances must be transported upright
Customs tariff number 8419 8998
Country of origin Federal Republic of Germany
WEEE-Reg.-No. DE 66812464
Dimensions approx incl.
carton
w x h x d: 660 x 890 x 650 mm
Net weight approx. 48 kg
Gross weight carton approx. 64 kg
Page 3/4 | 26.03.2018 | 2
